Distributor ready for connection OS-V1
Downloads
Oil shooter - OS
- for environmentally friendly and targeted lubrication
Targeted lubrication in inaccessible places...
Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist).
The function:
The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.
Note:
At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.
| Type: | Distributor ready for connection |
|---|---|
| Temperature min. [C°]: | -25 |
| Temperature max. [C°]: | 80 |
| Description: | Distributor ready for connection |
| Material: | Anodized aluminum |
| Viscosity range: | 10 - 150 mm²/sec (mittlere Öle) |
| Max. Cycle frequency per min.: | 160 |
| Product number: | OS-V1 |
| EAN: | 4255910813608 |
| Old Product number: | ÖS-V1 |
| Departures: | 2 |
| Type: | Distributor ready for connection |
|---|---|
| Temperature min. [C°]: | -25 |
| Temperature max. [C°]: | 80 |
| Description: | Distributor ready for connection |
| Material: | Anodized aluminum |
| Viscosity range: | 10 - 150 mm²/sec (mittlere Öle) |
| Max. Cycle frequency per min.: | 160 |
| Product number: | OS-V1 |
| EAN: | 4255910813608 |
| Old Product number: | ÖS-V1 |
| Departures: | 2 |
Ersatzteile OS-V1
Cutting ring EOS-SR6
€1.31*
EOS-SR6
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places... often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.
Bleed screw EOS-ES
€8.63*
EOS-ES
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places... often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.
Hose connector EOS-SV
€1.61*
EOS-SV
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places... often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.
Hose insertion sleeve EOS-EH
€0.56*
EOS-EH
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places... often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.
Accessories OS-V1
Brush BU-R20
€23.80*
BU-R20
Brushes for BMT, BKT and oil shooters OSThese brushes are ideal for the uncomplicated oiling of small surfaces, strips and belts. The medium is supplied from above via a hose (G1/8” connection). The BMT or BKT can be used here to supply oil.The stainless steel bracket BU-WI can be used for attachment to the machine or conveyor belt.Two M6x12 fastening screws are supplied. The BU-R12 and BU-R20 brushes can also be used in conjunction with the OS oil shooter.Miscellaneous:Included in the scope of delivery:1 x hose connection fitting (1030-6/4-1/8)2 x sealing ring (1600-1/8)Suitable for oil shooters
Brush BU-R10
€29.75*
BU-R10
Brushes for BMT, BKT and oil shooters OSThese brushes are ideal for the uncomplicated oiling of small surfaces, strips and belts. The medium is supplied from above via a hose (G1/8” connection). The BMT or BKT can be used here to supply oil.The stainless steel bracket BU-WI can be used for attachment to the machine or conveyor belt.Two M6x12 fastening screws are supplied. The BU-R12 and BU-R20 brushes can also be used in conjunction with the OS oil shooter.Miscellaneous:Included in the scope of delivery:1 x hose connection fitting (1030-6/4-1/8)2 x sealing ring (1600-1/8)