Oil shooter OS010-Z
€35.11*
OS010-Z
Delivery volume mm3:
10
|
Schlauchverlängerung:
with 2 m hose extension
Central lubrication for lubrication points that are difficult to access - OS...-Z- The detour lubricator...Confined spaces or lubrication points that can only be reached via detours are a headache for many a designer. Our OS metering valves can be equipped with a flexible PU hose extension (max. 2 m, outer Ø 4 mm) for this purpose. This allows you to direct your oil droplets around corners or into enclosed spaces (engine block, machine bed, etc.). Before commissioning, the PU hose is cut to the required length and simply filled with the relevant medium using the cartridge supplied. The supplied M3 threaded piece (width across flats 4.5 mm, nominal width 1.5 mm) is then attached to the end of the hose.
Variants from €28.80*
Distributor ready for connection OS-V4
€46.41*
OS-V4
Departures:
4
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places...Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.Note:At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.
Variants from €26.54*
Cutting ring EOS-SR4
€1.11*
EOS-SR4
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places... often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.
Oil shooter OS-BP/V
€827.05*
OS-BP/V
Gasket:
Viton
|
Volume L:
1,2
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places...Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.Note:At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.
Variants from €684.25*
Hose connector EOS-SV
€1.61*
EOS-SV
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places... often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.
Hose insertion sleeve EOS-EH
€0.56*
EOS-EH
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places... often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.
Cutting ring EOS-SR6
€1.31*
EOS-SR6
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places... often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.
Automatic sprayer AS
€176.72*
AS
Automatic sprayer - ASThe automatic sprayer works in a similar way to a windshield washer system on a car.
Actuation by hand or foot is replaced by a pneumatic cylinder that compresses a rubber bellows. This cylinder can be controlled via a 3/2-way valve. An adjusting screw on the cylinder rod makes the stroke adjustable. This regulates the amount of fluid.
Coupled with an automatic blower or a counter circuit (BA or ZS, see next pages), it is possible to apply oil in a targeted manner and work in pulses with a set cycle.Miscellaneous:1) Cylinder2) Adjusting screw3) Rubber bellows per switching cycle 10 ccm max./0.2 ccm min. medium Coolant or thin oils4) PVC hose, fully assembled Non-return valve (not visible) Non-return T-valve (not visible) Strainer filter (not visible)
Brush BU-R20
€23.80*
BU-R20
Brushes for BMT, BKT and oil shooters OSThese brushes are ideal for the uncomplicated oiling of small surfaces, strips and belts. The medium is supplied from above via a hose (G1/8” connection). The BMT or BKT can be used here to supply oil.The stainless steel bracket BU-WI can be used for attachment to the machine or conveyor belt.Two M6x12 fastening screws are supplied. The BU-R12 and BU-R20 brushes can also be used in conjunction with the OS oil shooter.Miscellaneous:Included in the scope of delivery:1 x hose connection fitting (1030-6/4-1/8)2 x sealing ring (1600-1/8)Suitable for oil shooters
BMT - Container, solenoid valve, dripper BMT24V-SS10PP
€390.32*
BMT24V-SS10PP
Control:
Voltage DC
|
Float switch:
with level switch for water and ethanol
BMT - Container, solenoid valve, dripper- BMT - the right metering unit for all brushes and roller lubricators.The 10 liter container (B) ensures sufficient lubricating fluid for continuous operation. The fluid level is clearly visible even from a distance. An optional level switch can be used to automate the filling of the container and prevent it from being completely emptied. By means of a solenoid valve (M) (24 V DC or 230 V AC - please specify when ordering), which is switched with the machine, the liquid reaches the dripper (T). The drip quantity can be metered separately for each felt roll using 2 throttle screws. The oil quantity can be checked via the viewing window in the dripper.
Variants from €331.42*
Brush BU-R10
€29.75*
BU-R10
Brushes for BMT, BKT and oil shooters OSThese brushes are ideal for the uncomplicated oiling of small surfaces, strips and belts. The medium is supplied from above via a hose (G1/8” connection). The BMT or BKT can be used here to supply oil.The stainless steel bracket BU-WI can be used for attachment to the machine or conveyor belt.Two M6x12 fastening screws are supplied. The BU-R12 and BU-R20 brushes can also be used in conjunction with the OS oil shooter.Miscellaneous:Included in the scope of delivery:1 x hose connection fitting (1030-6/4-1/8)2 x sealing ring (1600-1/8)
Solenoid valve OS-MV-2218-30
€129.71*
OS-MV-2218-30
Solenoid valve for additional lubrication circuitIdeal for integrating an additional lubrication circuit, this 2/2-way valve can switch on the circuit when the pump is at rest OS-BP (unpressurized).
Screw plug EOS-VS
€2.56*
EOS-VS
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places... often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.
BKT - Container, ball valve, dripper (for roller conveyors) BKT1/2-SS10PA
€313.57*
BKT1/2-SS10PA
Version:
Level switch PA
BKT - Container, ball shut-off valve, dripper (for roller lubricator)Container, ball shut-off valve, dripperAs with the BMT, the oil supply for roller lubricators or brushes can be metered and regulated. Instead of the solenoid valve, a ball shut-off valve has been installed here for purely manual operation. See BMT for remaining dimensions.
Variants from €255.26*
Bleed screw EOS-ES
€8.63*
EOS-ES
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places... often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.
Automatic sprayer AS/02
€122.57*
AS/02
Automatic sprayer - AS/02The automatic sprayer works in a similar way to a windshield washer system on a car.
Actuation by hand or foot is replaced by a pneumatic cylinder that compresses a rubber bellows. This cylinder can be controlled via a 3/2-way valve. An adjusting screw on the cylinder rod makes the stroke adjustable. This regulates the amount of fluid.
Coupled with an automatic blower or a counter circuit (BA or ZS, see next pages), it is possible to apply oil in a targeted manner and work in pulses with a set cycle.Miscellaneous:1) Cylinder2) Adjusting screw3) Rubber bellows per switching cycle 10 ccm max./0.2 ccm min. medium Coolant or thin oils4) PVC hose, fully assembled Non-return valve (not visible) Non-return T-valve (not visible) Strainer filter (not visible)
Cutting ring fitting OS-VW
€8.45*
OS-VW
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places... often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.
Drip oiler TO
€121.38*
TO
Drip oiler - TOThe transverse drip is essential for drilling, turning and milling machines and when drilling threads.
The drip oiler provides uniform lubrication at any desired point.
The drip quantity can be regulated and constantly monitored through the drip chamber. This practical device can be attached to almost all machines using the magnetic holder.ADVANTAGE
You do not need a power connection or a pump. Just make sure that the container is suspended above the metal hose.Included in the scope of delivery:1) Container with connection for hose 8 x 6 2) Drip chamber 3) PVC hose4) Push & pull fitting 5) Needle shut-off valve 6) Extension piece for metal hose 7) Metal hose 8) Attachment nozzle for metal hoseMiscellaneous:No power connection necessaryIncluded in the scope of delivery:1) Container with connection for hose 8 x 62) Drip chamber3) PVC hose4) Push & pull fitting5) Needle shut-off valve6) Extension piece for metal hose7) Metal hose8) Attachment nozzle for metal hose
Cutting ring fitting OS-VT
€10.12*
OS-VT
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places... often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.
Cutting ring fitting OS-VG
€4.22*
OS-VG
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places... often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.
Replacement cutting ring for screw connection OS-VSR
€0.62*
OS-VSR
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places... often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.
Level switch OS-S1,5-10
€115.43*
OS-S1,5-10
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places...Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (z.B. OS010). To connect the metering valve into the system, you need a distributor (OS-V1). Everything is supplied ready for connection, only the hoses (order no. S-PA4 for the fluid and S-PU4 for the pneumatic) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with two OS-V4 distributors. One OS-V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.Note:At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.
Level switch OS-S4,5-20
€151.13*
OS-S4,5-20
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places...Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (z.B. OS010). To connect the metering valve into the system, you need a distributor (OS-V1). Everything is supplied ready for connection, only the hoses (order no. S-PA4 for the fluid and S-PU4 for the pneumatic) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with two OS-V4 distributors. One OS-V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.Note:At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.