Oil shooter OS010-Z
€35.11*
OS010-Z
Delivery volume mm3:
10
|
Schlauchverlängerung:
with 2 m hose extension
Central lubrication for lubrication points that are difficult to access - OS...-Z- The detour lubricator...Confined spaces or lubrication points that can only be reached via detours are a headache for many a designer. Our OS metering valves can be equipped with a flexible PU hose extension (max. 2 m, outer Ø 4 mm) for this purpose. This allows you to direct your oil droplets around corners or into enclosed spaces (engine block, machine bed, etc.). Before commissioning, the PU hose is cut to the required length and simply filled with the relevant medium using the cartridge supplied. The supplied M3 threaded piece (width across flats 4.5 mm, nominal width 1.5 mm) is then attached to the end of the hose.
Variants from €28.80*
Replacement felt EF600
€452.20*
EF600
Roller diameter mm:
60
|
Roller length mm:
600
FR - Roller lubricatorReplacement felts can be reordered. Instead of “FR”, “EF” is used in the order number.
Variants from €23.80*
Distributor ready for connection OS-V4
€46.41*
OS-V4
Departures:
4
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places...Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.Note:At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.
Variants from €26.54*
Magnet holder MH
€22.61*
MH
Magnet holder - MHfor ZN, ZQ, MS, TO, AS.The magnetic holder is used to attach atomizers with metal hoses (see atomizers: ZQ; ZN; drip oiler (TO); automatic sprayer (AS)) and, of course, for other items. It can be attached quickly and easily to all magnetic surfaces without the need for assembly.
Cutting ring EOS-SR4
€1.11*
EOS-SR4
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places... often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.
Sieve ESV-PP
€9.46*
ESV-PP
Hose connectors, non-return valves, strainerHose connectors and non-return valves- made of plastic- Alcohol and acid resistant- Food-safe (LE version)Suitable for all PVC and PU hoses with a nominal diameter of 4 mm with the exception of the Y-piece EY6, which is intended for 6 mm hoses.
Non-return valve ERV/01
€7.74*
ERV/01
Hose connectors, non-return valves, strainerHose connectors and non-return valves- made of plastic- Alcohol and acid resistant- Food-safe (LE version)Suitable for all PVC and PU hoses with a nominal diameter of 4 mm with the exception of the Y-piece EY6, which is intended for 6 mm hoses.
Hose connector EOS-SV
€1.61*
EOS-SV
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places... often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.
Level switch SS10PA
€66.05*
SS10PA
Container with level switchThe fill level of a container can be queried via the level switch. The switch is available individually or including a container. The B-SS10PA and B-SS10PP versions are ideal for the oil supply of our ZMIN atomizer.The switch can be used as a minimum or maximum indicator. The switching function can be reversed by turning the switch through 180°.
Hose insertion sleeve EOS-EH
€0.56*
EOS-EH
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places... often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.
Metal hose EZMIN-MS
€101.75*
EZMIN-MS
Metal hoseMetal hose mounted for retrofitting or replacement suitable for ZMIN-MS.
Cutting ring EOS-SR6
€1.31*
EOS-SR6
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places... often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.
Sieve SIEB-PA
€3.69*
SIEB-PA
SieveOur “cleaners” filter contaminants from liquids such as oils, alcohols or alkalis and thus prevent annoying blockages. The SIEBe can be used in our or individual containers. They function independently of temperature in an unpressurized environment.
Adapter D-AD10
€72.59*
D-AD10
Size mm³:
10
Accessories for dosing systems (table-top and foot-mounted units)
Brush BU-R20
€23.80*
BU-R20
Brushes for BMT, BKT and oil shooters OSThese brushes are ideal for the uncomplicated oiling of small surfaces, strips and belts. The medium is supplied from above via a hose (G1/8” connection). The BMT or BKT can be used here to supply oil.The stainless steel bracket BU-WI can be used for attachment to the machine or conveyor belt.Two M6x12 fastening screws are supplied. The BU-R12 and BU-R20 brushes can also be used in conjunction with the OS oil shooter.Miscellaneous:Included in the scope of delivery:1 x hose connection fitting (1030-6/4-1/8)2 x sealing ring (1600-1/8)Suitable for oil shooters
PE plugs D-STPE10
€1.25*
D-STPE10
Material:
PE
|
Size mm³:
10
Accessories for dosing systems (table-top and foot-mounted units)
Dosing needle D-N38-051
€2.74*
D-N38-051
Length mm²:
38
|
Shape:
straight
|
Size inside mm³:
0,51
Accessories for dosing systems (table-top and foot-mounted units)
Variants from €1.39*
Compressed air timer PTV18
€70.81*
PTV18
Compressed air timer for atomizers - PTV18The pulse length can be set from 0.1 to 10 seconds on this compressed air timer.
It is simply connected into the compressed air line. As soon as the compressed air flows, the timer runs and then switches off automatically. The compressed air must be activated again for the next work cycle.Advantages:Low acquisition costsYou save on expensive electronicsIdeal for all atomizers and other fluid devices
Brush BU-R10
€29.75*
BU-R10
Brushes for BMT, BKT and oil shooters OSThese brushes are ideal for the uncomplicated oiling of small surfaces, strips and belts. The medium is supplied from above via a hose (G1/8” connection). The BMT or BKT can be used here to supply oil.The stainless steel bracket BU-WI can be used for attachment to the machine or conveyor belt.Two M6x12 fastening screws are supplied. The BU-R12 and BU-R20 brushes can also be used in conjunction with the OS oil shooter.Miscellaneous:Included in the scope of delivery:1 x hose connection fitting (1030-6/4-1/8)2 x sealing ring (1600-1/8)
Solenoid valve OS-MV-2218-30
€129.71*
OS-MV-2218-30
Solenoid valve for additional lubrication circuitIdeal for integrating an additional lubrication circuit, this 2/2-way valve can switch on the circuit when the pump is at rest OS-BP (unpressurized).
Closure plug D-STV10
€0.80*
D-STV10
Size mm³:
10
Accessories for dosing systems (table-top and foot-mounted units)
Roller lubricator holder FRH075-300
€101.15*
FRH075-300
FR - Roller lubricatorThe roller lubricator can be fixed in place with the FRH clamping brackets.
Screw plug EOS-VS
€2.56*
EOS-VS
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places... often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.
Roller lubricator holder FRHM050-150
€88.66*
FRHM050-150
FR - Roller lubricatorThe roller lubricator can be fixed in place with the FRH clamping brackets.
