OS-BP
Downloads
Oil shooter - OS
- for environmentally friendly and targeted lubrication
Targeted lubrication in inaccessible places...
Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist).
The function:
The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (z.B. OS010). To connect the metering valve into the system, you need a distributor (OS-V1). Everything is supplied ready for connection, only the hoses (order no. S-PA4 for the fluid and S-PU4 for the pneumatic) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with two OS-V4 distributors. One OS-V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.
Note:
At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.
| Type: | Pumpe mit Ölbehälter für Ölschießer |
|---|---|
| Temperature min. [C°]: | -25 |
| Temperature max. [C°]: | 80 |
| Description: | Tank + pump 1.2 L |
| Viscosity range: | 10 - 150 mm²/sec (mittlere Öle) |
| Max. Cycle frequency per min.: | 160 |
| Product number: | OS-BP |
| EAN: | 4255910813479 |
| Old Product number: | ÖS-BP |
| Volume [L]: | 1.2 |
| Gasket: | NBR |
| Pneumatic operating pressure [bar]: | 4 - 8 |
| Type: | Pumpe mit Ölbehälter für Ölschießer |
|---|---|
| Temperature min. [C°]: | -25 |
| Temperature max. [C°]: | 80 |
| Description: | Tank + pump 1.2 L |
| Viscosity range: | 10 - 150 mm²/sec (mittlere Öle) |
| Max. Cycle frequency per min.: | 160 |
| Product number: | OS-BP |
| EAN: | 4255910813479 |
| Old Product number: | ÖS-BP |
| Volume [L]: | 1.2 |
| Gasket: | NBR |
| Pneumatic operating pressure [bar]: | 4 - 8 |
Verwandte Produkte OS-BP
OS-BP4,5/V
€1,109.08*
OS-BP4,5/V
Gasket:
Viton
|
Volume L:
4,5
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places...Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (z.B. OS010). To connect the metering valve into the system, you need a distributor (OS-V1). Everything is supplied ready for connection, only the hoses (order no. S-PA4 for the fluid and S-PU4 for the pneumatic) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with two OS-V4 distributors. One OS-V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.Note:At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.
Variants from €684.25*
OS-BP4,5
€916.30*
OS-BP4,5
Gasket:
NBR
|
Volume L:
4,5
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places...Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (z.B. OS010). To connect the metering valve into the system, you need a distributor (OS-V1). Everything is supplied ready for connection, only the hoses (order no. S-PA4 for the fluid and S-PU4 for the pneumatic) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with two OS-V4 distributors. One OS-V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.Note:At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.
Variants from €684.25*
Oil shooter OS-BP/V
€827.05*
OS-BP/V
Gasket:
Viton
|
Volume L:
1,2
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places...Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.Note:At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.
Variants from €684.25*
Accessories OS-BP
Oil shooter OS025
€28.80*
OS025
Delivery volume mm3:
25
|
Schlauchverlängerung:
Without hose extension
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places...Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.Note:At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.
Distributor ready for connection OS-V4
€46.41*
OS-V4
Departures:
4
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places...Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.Note:At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.
Variants from €26.54*
Oil shooter OS010
€28.80*
OS010
Delivery volume mm3:
10
|
Schlauchverlängerung:
Without hose extension
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places...Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.Note:At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.
Level switch OS-S1,5-10
€115.43*
OS-S1,5-10
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places...Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (z.B. OS010). To connect the metering valve into the system, you need a distributor (OS-V1). Everything is supplied ready for connection, only the hoses (order no. S-PA4 for the fluid and S-PU4 for the pneumatic) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with two OS-V4 distributors. One OS-V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.Note:At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.
Distributor ready for connection OS-V1
€26.54*
OS-V1
Departures:
1
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places...Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.Note:At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.
Oil shooter OS100
€28.80*
OS100
Delivery volume mm3:
100
|
Schlauchverlängerung:
Without hose extension
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places...Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.Note:At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.
Dosing valve OS005
€33.92*
OS005
Delivery volume mm3:
5
|
Schlauchverlängerung:
Without hose extension
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places...Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.Note:At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.
Variants from €28.80*
Solenoid valve OS-MV-2218-30
€129.71*
OS-MV-2218-30
Solenoid valve for additional lubrication circuitIdeal for integrating an additional lubrication circuit, this 2/2-way valve can switch on the circuit when the pump is at rest OS-BP (unpressurized).
Oil shooter OS050
€28.80*
OS050
Delivery volume mm3:
50
|
Schlauchverlängerung:
Without hose extension
Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places...Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.Note:At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.