Oil sprayer system

“With our oil dispenser system, you achieve maximum results with minimal effort: The SOMMER-TECHNIK oil dispenser delivers every drop precisely to the lubrication point—cleanly, precisely, and efficiently, even in tight spaces.”

Cedrik Haenel
Procurator

Targeted lubrication in hard-to-reach areas…

Often, a precisely placed drop in the right place is enough to ensure reliable lubrication. This is exactly why we developed the oil injector (Art. OS-BP and OS-BP4.5). Depending on viscosity and cycle frequency, the system achieves a spray range of up to one meter. It is used wherever roominess is limited and clean application is required. The oil quantity is delivered to the lubrication point in a targeted and controlled manner, so that every drop is used effectively. In this way, lubrication is economical and does not produce harmful oil mist, protecting both the working environment and the health of customers.

How it works:

The built-in pump (Art.: OS-BP und OS-BP4,5) operates at a pneumatic operating pressure of 4 to 8 bar and is controlled by a 3/2-way valve, available in either 24 V DC or 230 V AC versions (item no. MV26-3218-30 = 24 VDC or MV26-3218-06 = 230 VAC). The pump container must be installed vertically, as shown. Here, the oil is fed into the lubrication lines at up to 50 bar via a built-in pressure intensifier.

The actual metering takes place cyclically via a metering valve, for example type OS010. With each switching pulse, a precisely defined amount of oil is released, creating the characteristic oil shot.

A distributor (Art. OS-V1) is required for the mounting of each metering valve. This serves both as a mechanical opening diameter and for venting the lubrication line. The distributors are supplied with all accessories required for initial commissioning. A maximum expansion to up to eight lubrication points is possible by using two OS-V4 distributors. The hoses required for the main line (Art. S-PA4) and compressed air connection (Art. S-PU4) must be ordered separately as required, cut to length as needed, and installed.

The metering valves used have fixed metering quantities between 5 and 100 mm³ per cycle and are not adjustable. Adaptation to different lubrication requirements is achieved by replacing the respective valve type.

It should be noted that as viscosity increases, the shot range and maximum cycle frequency decrease. Before initial commissioning, the system must be vented several times until the lubrication line is completely free of bubbles.

OS-BP

Gasket: NBR | Volume L: 1,2

Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places...Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (z.B. OS010). To connect the metering valve into the system, you need a distributor (OS-V1). Everything is supplied ready for connection, only the hoses (order no. S-PA4 for the fluid and S-PU4 for the pneumatic) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with two OS-V4 distributors. One OS-V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.Note:At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.

€684.25*

OS-BP4,5

Gasket: NBR | Volume L: 4,5

Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places...Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (z.B. OS010). To connect the metering valve into the system, you need a distributor (OS-V1). Everything is supplied ready for connection, only the hoses (order no. S-PA4 for the fluid and S-PU4 for the pneumatic) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with two OS-V4 distributors. One OS-V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.Note:At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.

Variants from €684.25*

€916.30*

Solenoid valve MV26-3218-30

MV26-3218-30

Good and cheapare the following standard valve series, which are available in either 24 VDC or 230 VAC.

€69.97*

Solenoid valve MV26-3218-06

MV26-3218-06

Good and cheapare the following standard valve series, which are available in either 24 VDC or 230 VAC.

€69.97*

Oil shooter OS010

OS010

Delivery volume mm3: 10 | Schlauchverlängerung: Without hose extension

Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places...Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.Note:At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.

€28.80*

Distributor ready for connection OS-V1

OS-V1

Departures: 1

Oil shooter - OS- for environmentally friendly and targeted lubricationTargeted lubrication in inaccessible places...Often only one drop is needed in the right place. The oil shooter sprays up to 1 m away (depending on viscosity and cycle frequency). It can be used wherever space is tight and clean. Every drop reaches its target. This means that lubrication can be economical and can be carried out without harming health (without oil mist). The function:The pneumatic operating pressure is 4 - 8 bar. The function is triggered via a 3/2-way valve (order no. MV26-3218-30 (= 24 VDC) or MV26-3218-06 (= 230 VAC)). The pump container must be installed vertically as shown. Here, the oil is pressed into the lines via a pressure cylinder at a pressure of up to approx. 50 bar. The oil quantity is released by the metering valve (5 - 100 mm³). Everything is supplied ready for connection, only the hoses (order no. S-PA4 - see table) have to be ordered, cut to length and screwed in according to your requirements. The maximum extension to up to 8 lubrication points is possible with 2 V4 distributors. One V1 distributor is placed in front of each metering valve to bleed the supply line. The metering valves have fixed metering quantities and are not adjustable. They can be replaced as required.Note:At higher viscosities, the shot range and cycle frequency decrease. Before initial commissioning, the system must be vented several times until it is completely bubble-free.

€26.54*